Expert Answers about Ford Crown Victoria
- Trailer Hitch Fit for 2011 Ford Crown Victoria
- The Curt Trailer Hitch # C12130 has been determined to fit the 2011 Ford Crown Victoria.
I have attached links to our hitch mount Class II cargo carriers and bike racks for 1-1/4 inch hitch receivers for you.
view full answer... - Will Draw-Tite Trailer Hitch 41116 Fit 2010 Ford Crown Victoria Police Interceptor w/Dual Exhaust
- First, you may not have to do anything with the exhaust because it appears that it may only affect Lincoln Town Car models. In the event that the exhaust on your PI Crown Vic is in the way of the hitch installation, the only modification is to move a hanger bracket. I have linked the instructions so you can see the possible modifications.
If you plan on doing some towing I recommend etrailer ball mount kit # EBMK4EL. It includes a ball mount, interchangeable ball set, a hitch pin with...
view full answer... - What Hitch Receiver Will Fit On My 2011 Crown Vic
- I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13707. It takes about 50 minutes to install, you won't need to drill holes in the frame.
If you have dual exhaust you will need to relocate the exhaust pipe hanger to provide adequate clearance for the pipe.
Next you will need wiring, I recommend the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
Item # C59236. This gives you the connection point to plug the 4-way from a trailer to your...
view full answer... - Will the OEM Trailer Hitch from a 1993 Mercury Grand Marquis Fit a 2001 Ford Crown Victoria
- I checked up on trailer hitch 88002 and found that it was an OEM hitch put on several vehicles. However, the 2001 Ford Crown Victoria is not one of the vehicles listed as a fit so I do not recommend trying to install it on the Ford.
For a hitch that will fit the Crown Vic the most popular Class III hitch is # 13707. I have included a link to a video showing a typical installation and a link to the installation instructions for you.
I also recommend the etrailer ball mount kit # EBMK4EL....
view full answer... - Best Trailer Wheel That Will Fit A 4.80-12 Tire
- It sounds you are looking for a new trailer wheel for your 4.80-12 trailer tires. Your 13 inch is like just a 12 inch wheel, but you may be measuring the overall diameter. Trailer wheel diameter is actually measured from bead seat to bead seat rather than overall, so a 12 inch diameter wheel may look more like a 13 inch diameter wheel. I'm guessing your wheel bolt pattern is actually 5 on 4-1/2 because 5 on 4.25 is not a common trailer wheel bolt pattern. I've attached a help article on...
view full answer... - Replacement Hardware Kit for Curt C12130 Hitch
- Yes, you can order an install kit for the Curt Trailer Hitch Receiver item # C12130. You will want the Replacement Hardware Kit for Trailer Hitches item # RHK. You will want to go to the product page and where it says item number put C12130 and under the manufacturer drop down select Curt.
view full answer... - Will the Konig Tire Chains # TH01221104 Fit My 235/55-17 Tires on My 2010 Ford Crown Victoria?
- Sorry about the confusion. If entered your 2010 Ford Crown Victoria into our fitguide and manually inputted your 235/55-17 tires, all of these listed tire chains will technically fit your tire size, but they have not been fitted on a 2010 Ford Crown Victoria specifically.
If you are looking at the Konig Standard Snow Tire Chains - Diamond Pattern - D Link - CB12 - Size 104 # TH01221104, those will fit 235/55-17 tires. In order to make sure these chains are safe to use on your Crown Victoria,...
view full answer... - Trailer Wiring for 2003 Ford Crown Victoria
- For the P71 police version of the 2003 Ford Crown Victoria there are only trailer wiring options that require splicing as there aren't any plug and play options. So the easiest option would be the ZCI part # 119250KIT which uses sensors instead of splices to connect to the vehicle wiring. The taillights of the police versions are different.
view full answer... - Rear Suspension Enhancement For A 1998 Ford Crown Victoria
- The Coil SumoSprings Custom Helper Springs for Coil Spring Suspension - Front or Rear Axle Item #
CSS-1125 are not compatible with the 1998 Ford Crown Victoria. To add suspension enhancement to the vehicle I recommend the Air Lift 1000 Air Helper Springs for Coil Springs - Rear Item # AL60798. This kit allows you to adjust the air pressure in each bag to support different weight added to the vehicle up 1000lbs for better ride quality.
view full answer... - The Curt 2 Inch Class III Hitch, # 13707, On A 1999 Ford Crown Victoria Seems Too Low To The Ground
- The Curt 2 Inch Class III Hitch, # 13707, is the correct hitch for your 1999 Ford Crown Victoria. It should measure 10-7/8 inches from the ground to the top of the receiver opening. If you are measuring to the bottom of the hitch it will be about 8-7/8 inches since it is a 2 inch hitch. This is not a problem with that vehicle.
If towing, you do need to use the recommended ball mount which is Draw-Tite Mount, # 2753. This ball mount when used in the 2-3/4 inch rise position will put the...
view full answer... - What Vehicles Does Trailer Hitch # C12130
- The Curt Trailer Hitch, # C12130, (installation instructions linked below) will fit the following vehicles:
1983 to 1991 Mercury Colony Park Wagon
1979 - 1991 Mercury Colony Park Wagon
1992 - 2011 Ford Crown Victoria
1992 - 2011 Mercury Grand Marquis
1983 - 1991 Mercury Grand Marquis excluding Wagon
1979 - 1986 Ford LTD Sedan
1979 - 1986 Ford LTD Wagon
1983 - 1991 Ford LTD Country Squire Wagon
1983 - 1991 Ford LTD Crown Victoria excluding Wagon
1983 - 1991 Ford LTD Crown Victoria Wagon
2003...
view full answer... - Will the K Source Universal Clip-On Towing Mirror # KS3891 Fit on a 2002 Crown Victoria
- The K Source Universal Clip-On Towing Mirror, # KS3891, was designed to fit as many different mirror styles as possible. I did some research on your 2002 Crown Victoria and I am confident that these mirrors will fit. The clips from this mirror will insert between the glass and the housing on your OEM mirrors.
Once you tighten the straps, the clips will pull against the mirror housing to secure the mirror. I have attached a demonstration video for you to check out.
view full answer... - Would the 20x48 inch Pro Series Cargo Carrier part # 6502 fit a 2001 Ford Crown Victoria
- As long as you had a hitch with a 2 inch opening installed on your 2001 Ford Crown Victoria like the Hidden Hitch part # 87408 yes, the 20x48 inch Pro Series Cargo Carrier part # 6502 that you referenced would work for you.
I attached a review video for this carrier for you to check out also.
view full answer...
Go To Results